http://www.ousob.com --- Legacy Redefined OuSob - File: /wwwroot/clipx/usr/include/linux/qic117.h

#ifndef _QIC117_H #define _QIC117_H /* * Copyright (C) 1993-1996 Bas Laarhoven, * (C) 1997 Claus-Justus Heine. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; see the file COPYING. If not, write to the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. * * $Source: /homes/cvs/ftape-stacked/include/linux/qic117.h,v $ * $Revision: 1.2 $ * $Date: 1997/10/05 19:19:32 $ * * This file contains QIC-117 spec. related definitions for the * QIC-40/80/3010/3020 floppy-tape driver "ftape" for Linux. * * These data were taken from the Quarter-Inch Cartridge * Drive Standards, Inc. document titled: * `Common Command Set Interface Specification for Flexible * Disk Controller Based Minicartridge Tape Drives' * document QIC-117 Revision J, 28 Aug 96. * For more information, contact: * Quarter-Inch Cartridge Drive Standards, Inc. * 311 East Carrillo Street * Santa Barbara, California 93101 * Telephone (805) 963-3853 * Fax (805) 962-1541 * WWW http://www.qic.org * * Current QIC standard revisions (of interest) are: * QIC-40-MC, Rev. M, 2 Sep 92. * QIC-80-MC, Rev. N, 20 Mar 96. * QIC-80-MC, Rev. K, 15 Dec 94. * QIC-113, Rev. G, 15 Jun 95. * QIC-117, Rev. J, 28 Aug 96. * QIC-122, Rev. B, 6 Mar 91. * QIC-130, Rev. C, 2 Sep 92. * QIC-3010-MC, Rev. F, 14 Jun 95. * QIC-3020-MC, Rev. G, 31 Aug 95. * QIC-CRF3, Rev. B, 15 Jun 95. * */ /* * QIC-117 common command set rev. J. * These commands are sent to the tape unit * as number of pulses over the step line. */ typedef enum { QIC_NO_COMMAND = 0, QIC_RESET = 1, QIC_REPORT_NEXT_BIT = 2, QIC_PAUSE = 3, QIC_MICRO_STEP_PAUSE = 4, QIC_ALTERNATE_TIMEOUT = 5, QIC_REPORT_DRIVE_STATUS = 6, QIC_REPORT_ERROR_CODE = 7, QIC_REPORT_DRIVE_CONFIGURATION = 8, QIC_REPORT_ROM_VERSION = 9, QIC_LOGICAL_FORWARD = 10, QIC_PHYSICAL_REVERSE = 11, QIC_PHYSICAL_FORWARD = 12, QIC_SEEK_HEAD_TO_TRACK = 13, QIC_SEEK_LOAD_POINT = 14, QIC_ENTER_FORMAT_MODE = 15, QIC_WRITE_REFERENCE_BURST = 16, QIC_ENTER_VERIFY_MODE = 17, QIC_STOP_TAPE = 18, /* commands 19-20: reserved */ QIC_MICRO_STEP_HEAD_UP = 21, QIC_MICRO_STEP_HEAD_DOWN = 22, QIC_SOFT_SELECT = 23, QIC_SOFT_DESELECT = 24, QIC_SKIP_REVERSE = 25, QIC_SKIP_FORWARD = 26, QIC_SELECT_RATE = 27, /* command 27, in ccs2: Select Rate or Format */ QIC_ENTER_DIAGNOSTIC_1 = 28, QIC_ENTER_DIAGNOSTIC_2 = 29, QIC_ENTER_PRIMARY_MODE = 30, /* command 31: vendor unique */ QIC_REPORT_VENDOR_ID = 32, QIC_REPORT_TAPE_STATUS = 33, QIC_SKIP_EXTENDED_REVERSE = 34, QIC_SKIP_EXTENDED_FORWARD = 35, QIC_CALIBRATE_TAPE_LENGTH = 36, QIC_REPORT_FORMAT_SEGMENTS = 37, QIC_SET_FORMAT_SEGMENTS = 38, /* commands 39-45: reserved */ QIC_PHANTOM_SELECT = 46, QIC_PHANTOM_DESELECT = 47 } qic117_cmd_t; typedef enum { discretional = 0, required, ccs1, ccs2 } qic_compatibility; typedef enum { unused, mode, motion, report } command_types; struct qic117_command_table { char *name; __u8 mask; __u8 state; __u8 cmd_type; __u8 non_intr; __u8 level; }; #define QIC117_COMMANDS {\ /* command mask state cmd_type */\ /* | name | | | non_intr */\ /* | | | | | | level */\ /* 0*/ {NULL, 0x00, 0x00, mode, 0, discretional},\ /* 1*/ {"soft reset", 0x00, 0x00, motion, 1, required},\ /* 2*/ {"report next bit", 0x00, 0x00, report, 0, required},\ /* 3*/ {"pause", 0x36, 0x24, motion, 1, required},\ /* 4*/ {"micro step pause", 0x36, 0x24, motion, 1, required},\ /* 5*/ {"alternate command timeout", 0x00, 0x00, mode, 0, required},\ /* 6*/ {"report drive status", 0x00, 0x00, report, 0, required},\ /* 7*/ {"report error code", 0x01, 0x01, report, 0, required},\ /* 8*/ {"report drive configuration",0x00, 0x00, report, 0, required},\ /* 9*/ {"report rom version", 0x00, 0x00, report, 0, required},\ /*10*/ {"logical forward", 0x37, 0x25, motion, 0, required},\ /*11*/ {"physical reverse", 0x17, 0x05, motion, 0, required},\ /*12*/ {"physical forward", 0x17, 0x05, motion, 0, required},\ /*13*/ {"seek head to track", 0x37, 0x25, motion, 0, required},\ /*14*/ {"seek load point", 0x17, 0x05, motion, 1, required},\ /*15*/ {"enter format mode", 0x1f, 0x05, mode, 0, required},\ /*16*/ {"write reference burst", 0x1f, 0x05, motion, 1, required},\ /*17*/ {"enter verify mode", 0x37, 0x25, mode, 0, required},\ /*18*/ {"stop tape", 0x00, 0x00, motion, 1, required},\ /*19*/ {"reserved (19)", 0x00, 0x00, unused, 0, discretional},\ /*20*/ {"reserved (20)", 0x00, 0x00, unused, 0, discretional},\ /*21*/ {"micro step head up", 0x02, 0x00, motion, 0, required},\ /*22*/ {"micro step head down", 0x02, 0x00, motion, 0, required},\ /*23*/ {"soft select", 0x00, 0x00, mode, 0, discretional},\ /*24*/ {"soft deselect", 0x00, 0x00, mode, 0, discretional},\ /*25*/ {"skip segments reverse", 0x36, 0x24, motion, 1, required},\ /*26*/ {"skip segments forward", 0x36, 0x24, motion, 1, required},\ /*27*/ {"select rate or format", 0x03, 0x01, mode, 0, required /* [ccs2] */},\ /*28*/ {"enter diag mode 1", 0x00, 0x00, mode, 0, discretional},\ /*29*/ {"enter diag mode 2", 0x00, 0x00, mode, 0, discretional},\ /*30*/ {"enter primary mode", 0x00, 0x00, mode, 0, required},\ /*31*/ {"vendor unique (31)", 0x00, 0x00, unused, 0, discretional},\ /*32*/ {"report vendor id", 0x00, 0x00, report, 0, required},\ /*33*/ {"report tape status", 0x04, 0x04, report, 0, ccs1},\ /*34*/ {"skip extended reverse", 0x36, 0x24, motion, 1, ccs1},\ /*35*/ {"skip extended forward", 0x36, 0x24, motion, 1, ccs1},\ /*36*/ {"calibrate tape length", 0x17, 0x05, motion, 1, ccs2},\ /*37*/ {"report format segments", 0x17, 0x05, report, 0, ccs2},\ /*38*/ {"set format segments", 0x17, 0x05, mode, 0, ccs2},\ /*39*/ {"reserved (39)", 0x00, 0x00, unused, 0, discretional},\ /*40*/ {"vendor unique (40)", 0x00, 0x00, unused, 0, discretional},\ /*41*/ {"vendor unique (41)", 0x00, 0x00, unused, 0, discretional},\ /*42*/ {"vendor unique (42)", 0x00, 0x00, unused, 0, discretional},\ /*43*/ {"vendor unique (43)", 0x00, 0x00, unused, 0, discretional},\ /*44*/ {"vendor unique (44)", 0x00, 0x00, unused, 0, discretional},\ /*45*/ {"vendor unique (45)", 0x00, 0x00, unused, 0, discretional},\ /*46*/ {"phantom select", 0x00, 0x00, mode, 0, discretional},\ /*47*/ {"phantom deselect", 0x00, 0x00, mode, 0, discretional},\ } /* * Status bits returned by QIC_REPORT_DRIVE_STATUS */ #define QIC_STATUS_READY 0x01 /* Drive is ready or idle. */ #define QIC_STATUS_ERROR 0x02 /* Error detected, must read error code to clear this */ #define QIC_STATUS_CARTRIDGE_PRESENT 0x04 /* Tape is present */ #define QIC_STATUS_WRITE_PROTECT 0x08 /* Tape is write protected */ #define QIC_STATUS_NEW_CARTRIDGE 0x10 /* New cartridge inserted, must read error status to clear. */ #define QIC_STATUS_REFERENCED 0x20 /* Cartridge appears to have been formatted. */ #define QIC_STATUS_AT_BOT 0x40 /* Cartridge is at physical beginning of tape. */ #define QIC_STATUS_AT_EOT 0x80 /* Cartridge is at physical end of tape. */ /* * Status bits returned by QIC_REPORT_DRIVE_CONFIGURATION */ #define QIC_CONFIG_RATE_MASK 0x18 #define QIC_CONFIG_RATE_SHIFT 3 #define QIC_CONFIG_RATE_250 0 #define QIC_CONFIG_RATE_500 2 #define QIC_CONFIG_RATE_1000 3 #define QIC_CONFIG_RATE_2000 1 #define QIC_CONFIG_RATE_4000 0 /* since QIC-117 Rev. J */ #define QIC_CONFIG_LONG 0x40 /* Extra Length Tape Detected */ #define QIC_CONFIG_80 0x80 /* QIC-80 detected. */ /* * Status bits returned by QIC_REPORT_TAPE_STATUS */ #define QIC_TAPE_STD_MASK 0x0f #define QIC_TAPE_QIC40 0x01 #define QIC_TAPE_QIC80 0x02 #define QIC_TAPE_QIC3020 0x03 #define QIC_TAPE_QIC3010 0x04 #define QIC_TAPE_LEN_MASK 0x70 #define QIC_TAPE_205FT 0x10 #define QIC_TAPE_307FT 0x20 #define QIC_TAPE_VARIABLE 0x30 #define QIC_TAPE_1100FT 0x40 #define QIC_TAPE_FLEX 0x60 #define QIC_TAPE_WIDE 0x80 /* Define a value (in feet) slightly higher than * the possible maximum tape length. */ #define QIC_TOP_TAPE_LEN 1500 /* * Errors: List of error codes, and their severity. */ typedef struct { char *message; /* Text describing the error. */ unsigned int fatal:1; /* Non-zero if the error is fatal. */ } ftape_error; #define QIC117_ERRORS {\ /* 0*/ { "No error", 0, },\ /* 1*/ { "Command Received while Drive Not Ready", 0, },\ /* 2*/ { "Cartridge Not Present or Removed", 1, },\ /* 3*/ { "Motor Speed Error (not within 1%)", 1, },\ /* 4*/ { "Motor Speed Fault (jammed, or gross speed error", 1, },\ /* 5*/ { "Cartridge Write Protected", 1, },\ /* 6*/ { "Undefined or Reserved Command Code", 1, },\ /* 7*/ { "Illegal Track Address Specified for Seek", 1, },\ /* 8*/ { "Illegal Command in Report Subcontext", 0, },\ /* 9*/ { "Illegal Entry into a Diagnostic Mode", 1, },\ /*10*/ { "Broken Tape Detected (based on hole sensor)", 1, },\ /*11*/ { "Warning--Read Gain Setting Error", 1, },\ /*12*/ { "Command Received While Error Status Pending (obs)", 1, },\ /*13*/ { "Command Received While New Cartridge Pending", 1, },\ /*14*/ { "Command Illegal or Undefined in Primary Mode", 1, },\ /*15*/ { "Command Illegal or Undefined in Format Mode", 1, },\ /*16*/ { "Command Illegal or Undefined in Verify Mode", 1, },\ /*17*/ { "Logical Forward Not at Logical BOT or no Format Segments in Format Mode", 1, },\ /*18*/ { "Logical EOT Before All Segments generated", 1, },\ /*19*/ { "Command Illegal When Cartridge Not Referenced", 1, },\ /*20*/ { "Self-Diagnostic Failed (cannot be cleared)", 1, },\ /*21*/ { "Warning EEPROM Not Initialized, Defaults Set", 1, },\ /*22*/ { "EEPROM Corrupted or Hardware Failure", 1, },\ /*23*/ { "Motion Time-out Error", 1, },\ /*24*/ { "Data Segment Too Long -- Logical Forward or Pause", 1, },\ /*25*/ { "Transmit Overrun (obs)", 1, },\ /*26*/ { "Power On Reset Occurred", 0, },\ /*27*/ { "Software Reset Occurred", 0, },\ /*28*/ { "Diagnostic Mode 1 Error", 1, },\ /*29*/ { "Diagnostic Mode 2 Error", 1, },\ /*30*/ { "Command Received During Non-Interruptible Process", 1, },\ /*31*/ { "Rate or Format Selection Error", 1, },\ /*32*/ { "Illegal Command While in High Speed Mode", 1, },\ /*33*/ { "Illegal Seek Segment Value", 1, },\ /*34*/ { "Invalid Media", 1, },\ /*35*/ { "Head Positioning Failure", 1, },\ /*36*/ { "Write Reference Burst Failure", 1, },\ /*37*/ { "Prom Code Missing", 1, },\ /*38*/ { "Invalid Format", 1, },\ /*39*/ { "EOT/BOT System Failure", 1, },\ /*40*/ { "Prom A Checksum Error", 1, },\ /*41*/ { "Drive Wakeup Reset Occurred", 1, },\ /*42*/ { "Prom B Checksum Error", 1, },\ /*43*/ { "Illegal Entry into Format Mode", 1, },\ } #endif /* _QIC117_H */